Xpelair CF20 User Manual download pdf (Page 5)

Tilbehør

For å forenkle installasjonen og

spare tid, kan det være at din

installasjon krever noe av

tilbehøret som er listet opp

nedenfor:

WD100 Vegg-gjennomføring

CFWG100 Vegg-gitter

FDA Utstyrspakke med

plant kanaladapter

XCT100 Kondensavskiller

DGW/B Gitterluke for

luftutskiftning

SP100 Muffeplate

XAA Luftadapter for mur

VC10 Avtrekksdeksel

WT10 Kanalavslutnings-sett

XF/FM Plan rørkanal

(plast/metall)

(plast 234 x 29 mm

metall 230 x 25 mm)

VK10 Veggventil-sett

FD100 Fleksibel rørkanal

WDC5 Snekkeskrue-klips

XCMK Sett for montering i

himling

XBP In-line

tilbakeslippsklaff

EFT Lettmontert

avslutnings-sett

GMK Sett for montering i

vindu

PDXGF Fettfilter

Nedenfor er det listet opp enkelte

reservedeler som er tilgjengelige.

Se baksiden på denne trykksaken

for bestillingsinformasjon:

41520SK Monterings-sett

(komplett)

41528SK Rund muffe (komplett)

41731SK Motor (DX200)

41733SK Motor (CF20/CF20T/

DX200T)

41782SK Kretskort-komponent

(DX200T)

41735SK Kretskort-komponent

(CF20)

41736SK Kretskort-komponent

(CF20T)

41737SK Frontdeksel kompl.

med mottrykksplate

(DX200)

41738SK

Frontdeksel kompl. med

mottrykksplate (DX200T)

41739SK

Frontdeksel kompl. med

mottrykksplate

(CF20/CF20T)

41740SK Innfatningsprofil

(komplett)

41741SK

Snorbryter-komponent

(CF20/CF20T)

41742SK Viftehjul (komplett)

Tillbehör

I listan nedan hittar du hjälpmedel

som kan vara av nytta under

installationen:

WD100 Väggtrumma

CFWG100 Väggaller

FDA Adaptorsats för

planmontering

XCT100 Kondensavledare

DGW/B Luftregleringsgaller

SP100 Mufförbindningsplatta

XAA Adapter

VC10 Ventilhuv

WT10 Avspänningssats

XF/FM Planmontering

(plast/metall)

(plast 234 x 29 mm)

(metall 230 x 25 mm)

VK10 Väggventilsats

FD100 Flexibel

ledningsdragning

WDC5 Skruvdriftsklämmor

XCMK Takmonteringssats

XBP Svart reglerventil

EFT Avspänningssats

GMK Glasmonteringssats

PDXGF Smörjningsfilter

I listan nedan hittar du

reservdelar. Du hittar

beställningsinformation på denna

bruksanvisnings baksida:

41520SK Fastsättningssats

(komplett)

41528SK Mufförbindning

(komplett sortiment)

41731SK Motor (DX200)

41733SK Motor (CF20/CF20T/

DX200T)

41782SK PCB-montering

(DX200T)

41735SK PCB-montering

(CF20)

41736SK PCB-montering

(CF20T)

41737SK Främre skydd med

skärm (DX200)

41738SK Främre skydd med

skärm (DX200T)

41739SK

Främre skydd med

skärm (CF20/CF20T)

41740SK Ramformning

(komplett sortiment)

41741SK Dragsnöresmontering

(CF20/CF20T)

41742SK Fläkthjul (komplett

sortiment)

Accessori opzionali

Per un’installazione più facile e

veloce, potrebbero essere

necessari alcuni degli accessori

sottoelencati:

WD100 Condotto per parete

CFWG100 Grata per parete

FDA Kit adattatore per

condotto piatto

XCT100

Pozzetto di

intercettazione della

condensa

DGW/B Grata dello sportello di

ricambio aria

SP100 Piastra di imbocco

XAA Adattatore per mattoni

traforati

VC10 Cappottatura di

ventilazione

WT10 Kit di terminazione

condotti

XF/FM Condotti piatti

(plastica/metallo)

(plastica 234 x 29mm,

metallo 230 x 25mm)

VK10 Kit di ventilazione per

parete

FD100 Condotti flessibili

WDC5 Fermagli a vite senza

fine

XCMK Kit di montaggio al

soffitto

XBP Otturatore in linea del

tiraggio di ritorno

EFT Kit di terminazione di

facile montaggio

GMK Kit per il montaggio su

vetro

PDXGF Filtro antigrasso

Qui di seguito sono elencati alcuni

dei ricambi disponibili. Per

informazioni su come ordinarli,

consultare la quarta di copertina:

41520SK Kit di fissaggio (kit

intero)

41528SK Imbocco a bicchiere

circolare (intera

gamma)

41731SK Motorino (DX200)

41733SK Motorino (CF20/

CF20T/DX200T)

41782SK Gruppo PCB

(DX200T)

41735SK Gruppo PCB (CF20)

41736SK Gruppo PCB (CF20T)

41737SK Coperchio anteriore

completo di

diaframma (DX200)

41738SK Coperchio anteriore

completo di

diaframma (DX200T)

41739SK Coperchio anteriore

completo di

diaframma

(CF20/CF20T)

41740SK

Modanatura della

cornice

(intera gamma)

41741SK

Gruppo cordicella

(CF20/CF20T)

41742SK

Girante (intera

gamma)

Συµπληρωµατικές Επιλογές

Γι α γρήγορη και εύκολη

εγκατάσταση, η εγκατάσταση

σας µπορεί να χρειαστεί µερικά

απ τα Συµπληρωµατικά που

αναφέρονται πιο κάτω:

WD100 Αγωγς τοίχου

CFWG100 Κιγκλίδωµα τοίχου

FDA Προσαρµογέας

επίπεδου αγωγού

XCT100 Ατµοπαγίδα

DGW/B Κιγκλίδωµα πρτας

ανανέωσης αέρα

SP100 Πλάκα βύσµατος

XAA Προσαρµογέας

τούβλου αέρα

VC10

Κάλυµµα αεραγωγού

WT10 Σύνολο αγωγού

τερµατισµού

XF/FM Επίπεδος αγωγς

(πλαστικ/µέταλλο)

(Πλαστικ 234 χ 29 χλστ.

Μέταλλο 230 χ 25 χλστ.)

VK10 Σύνολο αεραγωγού

τοίχου

FD100 Εύκαµπτος αγωγς

WDC5 Κλιπ οφιοειδούς

κίνησης

XCMK

Σύνολο τοποθέτησης

σε ταβάνι

XBP Φράχτης

οπισθοδροµικού

ρεύµατος in-line

EFT Σύνολο

τερµατισµού

εύκολης εφαρµογής

GMK

Σύνολο τοποθέτησης

γυαλιού

PDXGF Φίλτρο γράσου

Πιο κάτω αναφέρονται µερικά

απ τα διαθέσιµα ανταλλακτικά.

Συµβουλευθείτε την πίσω ψη

του παρντος φυλλαδίου για

λεπτοµέρειες παραγγελίας:

41520SK Σύνολο στερέωσης

(ολκληρο σύνολο)

41528SK Κυκλικ βύσµα

41731SK Μοτέρ (DX200)

41733SK

Μοτέρ (CF20/CF20T/

DX200T)

41782SK

Σύνολο PCB (DX200T)

41735SK Σύνολο PCB (CF20)

41736SK

Σύνολο PCB (CF20T)

41737SK

Μπροστιν κάλυµµα

συνοδευµενο απ

εκτροπέα (DX200)

41738SK Μπροστιν

κάλυµµα

συνοδευµενο απ

εκτροπέα (DX200T)

41739SK

Μπροστιν κάλυµµα

συνοδευµενο απ

εκτροπέα (CF20/CF20T)

41740SK Χυτ πλαίσιο

(ολκληρη σειρά)

41741SK Σύνολο κορδονιού

τραβήγµατος

(CF20/CF20T)

41742SK Στροφείο

(ολκληρη σειρά)

N S I GR

For speed and ease of Installation, your installation may require some of the

Ancillaries indicated in “Ancillary Options”.

If installing on a wall (surface mounting)

1. Mark on the wall the centre of the duct hole A.

2. Use this centre to cut an opening through the wall 117mm dia, with a slight

fall to the exterior.

3. Fit the wall duct (WD100), not supplied, and mortar into place.

If installing on a wall (flush mounting)

1. Mark on the wall the centre of the duct hole A, and drill a pilot

hole through both walls at a slight downward angle.

2. Use the centre to mark a rectangular hole for the inner wall using the

dimensions

3. Cut the rectangular hole through the inner wall.

4. Go outside and cut a 117mm-diameter hole in the outer wall using the small

hole as the centre.

5. Measure the wall thickness.

Cut the wall duct (WD100), not supplied, so that it is 64mm less than the

wall thickness.

If installing in a ceiling (surface mounting)

This method requires a space above the ceiling, such as a loft or attic, to provide

access for 100mm internal diameter ducting.

1. Mark on the ceiling the centre of the duct hole A, avoiding ceiling joists and

buried cables etc.

2. Cut a 117mm-diameter hole using the marked centre.

If installing in a ceiling (flush mounting)

For 100mm diameter ducting:

1. Mark a rectangular hole using the dimensions

2. Cut the hole, avoiding ceiling joists and buried cables etc.

For flat ducting:

• This fan can be installed within a 47mm void without the circular spigot

(Fig.E). Flat ducting adapter kit (FDA) available.

Preparing the fan for installation

1. Remove the front cover 2 (Fig.C)

2. Fit the foam tape

!™ supplied around the circular spigot 7 (Fig.E).

3. Remove the electrical cover

5 (Fig.E). The impeller can be removed to

ease access (if required). This is a "push-on/pull-off" assembly.

Setting the fan speed

DX200T / CF20 / CF20T Only (Fig.D)

4. The correct condensation control speed (CF20/CF20T) or operating speed

(DX200T) should be selected to suit the room size in which the fan is to be

installed. Slide the switch

X to the required position. Please note that the

fan is factory set to “Position 2”.

5. Switch Position Size / Room Volume (m

)

1 Large (34 and above)

2 Medium (28 – 34)

3 Small (less than 28)

Setting the trickle speed

DX200T / CF20 / CF20T Only (Fig.D)

6. The fan can be set so that it provides constant trickle extraction. Slide the

switch

Y to the required position. Please note that the fan is factory set to

“Position 0”.

7. Switch Position Setting

0Trickle extraction OFF

ITrickle extraction ON

Setting the time delay start

DX200T / CF20T Only (Fig.D)

8. The fan can be set so that there is a 2-minute delayed start to its

operation when used with an external on/off switch. Slide the

switch

Z to the required position. Please note that the fan is

factory set to “Position 0”.

Switch Position Setting

0Time delay start OFF

ITime delay start ON

Mounting the fan on a wall or ceiling (surface mounting)

1. Place the ducting into the hole and align to the required position. If wall

mounting, ensure that the ducting slopes down and away from the fan

2. Mark the positions of the three fixing holes

A in Fan box 6 (Fig.E).

3. If wall mounting, drill three holes 5.5mm diameter for wall plugs (supplied).

If ceiling mounting

B , use appropriate fasteners (not supplied).

4. Cut out the cable inlet hole, if required, in the surround

0 and slit the cable

grommet. Slide the surround

0 over the fan box 6.

5. Pass the electrical cables into the fan box

6 through the rear cable inlet

hole and surround, and re-fit the cable grommet.

Ensure that cable grommet is in place and a tight fit.

6. Offer the fan box 6 up to the wall or ceiling. Ensure the circular spigot 7

enters the ducting.

7. Fix the fan box

6 to the wall using screws 8 or to the ceiling using

appropriate fasteners (not supplied).

If mounting in a wall (flush mounting)

The surround 0 is not required. Fit the ducting to the circular spigot 7.

If the hole size is as recommended:

1. Assemble the three fan body clamps 9 to the fan box 6 using screws 8.

2. Slit the cable grommet. Pass the electrical cables into the fan box

through the cable inlet hole and cable grommet.

Ensure cable grommet is in place and a tight fit.

3. Offer the fan box 6 up to the wall.

4. Tighten up the three screws

8 until the fan is clamped to the inner wall.

The fan body clamps

9 will rotate to an automatic stop position. DO NOT

OVERTIGHTEN

If the hole size is larger than recommended i.e.: larger than the flange on the

fan box

(Mostly relating to “retro-fit” installations):

1. The fan body clamps ARE NOT suitable. Construct a wooden frame of

INTERNAL dimensions 203 x 233mm. Depth should be at least 50mm. Fit the

1. READ ALL THESE INSTRUCTIONS & WARNINGS FULLY BEFORE COMMENCING INSTALLATION.

2. INSTALLATIONS AND WIRING MUST CONFORM TO CURRENT IEE REGULATIONS (UK), LOCAL OR APPROPRIATE

REGULATIONS (OTHER COUNTRIES). IT IS THE INSTALLER’S RESPONSIBILITY TO ENSURE THAT THE APPROPRIATE

BUILDING CODES OF PRACTICE ARE ADHERED TO.

3. A QUALIFIED ELECTRICIAN MUST SUPERVISE ALL INSTALLATIONS.

4. THESE APPLIANCES ARE INTENDED FOR CONNECTION TO FIXED WIRING

5. CHECK THAT THE ELECTRICAL RATING SHOWN ON THE FAN MATCHES THE MAINS SUPPLY.

WARNING: THESE APPLIANCES MUST BE EARTHED.

7. SITE AWAY FROM DIRECT SOURCES OF HEAT (I.E.: GAS COOKERS OR EYE-LEVEL GRILLS) AND NOT WHERE

AMBIENT TEMPERATURES ARE LIKELY TO EXCEED 50˚C.

8. WHEN THE FAN IS INSTALLED IN A ROOM CONTAINING A FUEL BURNING APPLIANCE, PRECAUTIONS MUST BE TAKEN TO

AVOID THE BACKFLOW OF GASES INTO THE ROOM FROM THE OPEN FLUE OF THE FUEL BURNING APPLIANCE.

9. ENSURE THAT ALL RELEVANT SAFETY PRECAUTIONS (CORRECT EYE PROTECTION AND PROTECTIVE CLOTHING

ETC) ARE TAKEN WHEN INSTALLING AND MAINTAINING THIS FAN.

10. GENERAL GUIDANCE FOR SITING THE FAN SEE “FIG. G”. ALWAYS SITE FAN AS HIGH AS POSSIBLE

11. IF ANY SECTION OF THE DUCTWORK IS POSITIONED HIGHER THAN THE FAN A CONDENSATION TRAP (XCT100) MUST

BE FITTED AS CLOSE AS POSSIBLE TO THE FAN.

IMPORTANT

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comments to this Manuals

No comments

Xpelair CF20 User Manual Page 5

Comments to this Manuals

Related products and manuals for Unknown Xpelair CF20